Zappers&Devices-How to Build Them

[amadeus]

I hope that in this thread we could gather all practical information of how to build different 'electro medicine' devices, (e.g. Zappers, Bob Beck-, Rife etc.)
I have some experience in electronics, but I'm hoping that those who are professionals in the field would help us all in simplifying the designs, correcting any errors and really make the devices available for everyone.

So let's start and make everyones lives healthier! :)

[amadeus]

The first device I've built is the original design of the Hulda Clark zapper. It's the same design as in the book "The cure for all diseases" with one exception: A resistor (R5) has been added (By Hulda Clark) that gives every pulse an added Positive Offset of 1/4 volt.

The design:
http://img128.imageshack.us/img128/5523/zapschematicit1.gif


Because of the actual appearance of the 555-timer circuit(the pin numbers are a bit different) the design above is a bit confusing. I have made a design of it using the LT-Spice simulator program and it looks like this:

http://img266.imageshack.us/img266/8680/spicezapper1lg7.png

I found it easier to build the zapper using the LT-Spice schematics above. Remember that all crossing wires in the Spice-design are NOT connected, only the ones with a little square(node).

The output looks like this:

http://img266.imageshack.us/img266/9649/spicezapper3pl8.png

[amadeus]

Sorry, the Spice-design was a bit unclear about where to connect the hand holds. You just connect one wire (e.g. black) to the negative pole of the battery(earth) and a another wire (e.g. red) to the position where the circle is in the design(below R5-that's the output). And remember to disconnect the battery after use, or add the switch(see original schematic), otherwise the battery will be drained in no time.

About the hand holds:
In "The Cure for all Disease", Hulda Clark specifies 3/4" x 4" copper pipes for hand holds. 1" diameter copper pipes are available at some building supply stores, like Home Depot, instead of the 3/4" pipes. Although it is expensive, 1" pipe is much more comfortable to hold, and provides a larger surface area, decreased resistance, and more current. For a 1" pipe, put a 1.25 x 10/24 SS bolt through one end to attach the alligator clips. Cut the pipe to 5" instead of 4" of one has large hands to increase area, if desired.

Grasping the copper handholds directly is not recommended by Clark because of the potential to absorb the metal through the skin. This also leads to variable resistance since it depends on the salt and moisture present on the palms. Clark instructs to use a single strip of wet paper towel wrapped around the hand holds.

[amadeus]

How to use it:

Hulda Clark's instructions are to zap for 7 minutes, wait 20 minutes. This kills any larger parasites like worms in the body according to her, as well as any free bacteria, viruses, and such. Then on another 7 minutes followed by another 20 minute break. This is to kill any bacteria and viruses which were inhabiting the body of the larger parasites. Then a final 7 minutes on. This mops up any viruses which were inhabiting the bacteria. This is a total of 61 minutes. It is necessary to do this daily for at least a month to clear chronic pathogens which respond to a zapper. The body's cells are not harmed by the zapper, so any viruses, fungi, and such which are inside the cells will be gotten eventually. Afterwards, zapping once a week is all that is necessary except in the case of serious disease, where Clark recommends daily until better since it is so easy to pick up parasites and other pathogens. NEVER zap for only one or two 7 minute sessions. Always do the full regimen of three.

It is best to swap hands with electrodes between each 7 minute session. I don't know if charge buildup is a problem, causing electrical imbalance as some speculate, but it is prudent to swap hands at least once during the sessions.

[startzpe]

Here's the info on how and why to build a Beck Protocol Unit

32 Page PDF file "Take Back your Power" (http://www.cancertutor.com/Cancer02/BobBeckPaper.pdf)

http://www.sharinghealth.com/images/beckSchematicImproved.gif

http://www.sharinghealth.com/beckprotocol/buildyourown.html

This 11/24/1996 page describes a "Plant Growth Stimulator" improved since my 1991 design. User-tested for over two years, it is solid state (no relays), uses three (not seven) batteries, makes colloids, is much smaller, lighter, silent, with battery saving features, and is available as a mostly-assembled kit complete with electrodes and silver for about $100 US$.
NOTE: Due to government harassment, assembled kits may not be available anymore.


How to Build a Magnetic Pulser (http://www.newmediaexplorer.org/chris/2003/08/19/build_a_low_cost_simple_magnetic_pulser.htm)

[amadeus]

Thanks 'startzpe'. The bob beck device is the next device I'm going to assemble. Have you built this one yourself? I'm ordering the parts soon, any hints regarding the building?

[serpentoffire]

WOW I was an electronic designer and I don't see a 555 since long time ago.
Yes both are oscillators but what is the impact of these devices in human body? I know that 400Mhz-1GHz EM frequencies have interaction with human cells. 4Hz is a very very very long wave that haven't interaction with nothing of the same wavelength in our body.

Please explain me which human process is involved.

[amadeus]

WOW I was an electronic designer and I don't see a 555 since long time ago.
Yes both are oscillators but what is the impact of these devices in human body? I know that 400Mhz-1GHz EM frequencies have interaction with human cells. 4Hz is a very very very long wave that haven't interaction with nothing of the same wavelength in our body.

Please explain me which human process is involved.

Welcome to the thread. All us interested in these devices would appreciate your expertize. A good start to get to know the field of 'electromedicien' is to read 'The Body Electric'. by Dr. Robert Becker. (http://www.amazon.com/Body-Electric-Electromagnetism-Foundation-Life/dp/0688069711) Also the PDF 'Take Back your Power" (see startzpe's post) is interesting. It is also amazing to find these (http://www.patentstorm.us/patents/5817142-description.html) many patents concerning the proven effects of blood electrification. I think it's at least worth looking into and try for yourself before judging.;)

[amadeus]

'frank1974' has provided excellent advice on how to build Bob Beck's blood purifier ('Plant Growth Stimulator') in THIS (http://www.davidicke.com/forum/showthread.php?p=188965&posted=1#post188965) thread. Thanks frank! :):):)

[amadeus]

Some Youtube clips and a blog of how to make your own PCB:

How to make a PCB (http://www.youtube.com/watch?v=Q6WJqjVleG0&NR=1)

Make Your Own Printed Circuit Boards on a Laserjet! (http://www.youtube.com/watch?v=urv6jArKp6M)

PCB etching with inkjet picture paper (http://www.youtube.com/watch?v=snileUK7PQg)

Blog: How to make your own PCBs (http://styley.net/?p=52#more-52)

[startzpe]

... if you apply a direct current (DC) potential to the skin, you're going to get an electrolysis effect and that can cause problems, so Beck designed a circuit that varied the voltage with an alternating current (AC) at a very low frequency and avoided the electrolysis problem. The waveform that Beck chose is not the typical sine wave seen in AC household outlets, but rather is a bi-phasic square wave. Square waves generate a large number of harmonics. Harmonics are frequency multibles of the original frequency. For example, a 4 Hertz (hz) square wave can produce harmonics (with the right equipment) of 8 hz, 16 hz, 32 hz, etc. right up into the radio frequency range. Beck finally settled on 3.92 hz as the ideal base frequency and assembled a schematic of the simple square wave oscillator , including a complete parts list. He used short, one inch lengths of stainless steel welding rods with attached wires for electrodes and started to experiment on himself.

http://72.14.253.104/search?q=cache:N8Zwfc_sUQQJ:www.riferesonator.com/bio-electro.htm+resonance+3.92+beck&hl=en&ct=clnk&cd=1

[amadeus]

I found another discussion group on Zapper devices, check it out:
Zapper & Pulse Generator Support Forum (http://curezone.com/forums/f.asp?f=292)

The parent directory with several other forums is also interesting with tons of stuff:
CureZone Forums (http://curezone.com/forums/)

P.s. It is funny how the "inventors" of th Parazapper- and The Ultimate zapper device keep attacking each other on the zapper forum. I find the Ultimate zapper guy suspicious, his tactics on promoting his own device seem pathological. You can read the thread here. (http://curezone.com/forums/am.asp?i=960152&s=1#i1)

[amadeus]

Another thing, the devices that are sold as zappers are square wave oscillators. So in stead of buying a expensive "zapper deluxe" you could just buy a "square wave oscillator kit" like this:

http://img218.imageshack.us/img218/479/squarewavepremadebn3.jpg

Schematics for this one:

http://img340.imageshack.us/img340/2711/squarewaveosccctan6.gif

These images were taken from THIS (http://www.talkingelectronics.com/projects/SquareWaveOsc/SquareWaveOsc.html) site. The design is simple but still allowing the user to change the frequency, great! Another example of an "oscillator kit" can be found HERE. (http://store.qkits.com/moreinfo.cfm/QK111)

[serpentoffire]

You make me young showing these things. One of my creations:

http://i241.photobucket.com/albums/ff118/serpentoffire/msx.gif